進口電磁閥說明書

使 用 說 明 書

Use  that  book   tomorrow

一、應用范圍Applications

德國萊克LIK品牌-進口電磁閥廣泛應用在航天、船舶重工、石油化工、工業爐窯、鍋爐、給排水、采暖空調、消防設備、干燥設備食品醫療設備、清洗設備、景觀灌溉、噴泉、水廠等管道系統中.

High pressure solenoid valveIt is widely used in aerospace, shipbuilding Heavy Industry, petrochemical, industrial furnaces, boilers, plumbing, heating and air conditioning, fire-fighting equipment, drying equipment，Food medical equipment, cleaning equipment, landscape irrigation, fountains, water and other piping systems

二、產品特點Features

☆不銹鋼活塞式，動作靈敏，壽命長達100萬次；專制線圈不易燒毀；閥安裝方向無限制；適用范圍廣

 ☆Stainless steel piston, movement sensitive, life is 100 million times; autocratic coil easily burned; valve installed on the direction of unrestricted; for a wide range of

三、工作原理Work

☆常閉型：線圈通電時，主閥芯靠介質壓差力打開；線圈斷電，閥關閉。

☆常開型：線圈通電時，閥關閉；線圈斷電，主閥芯靠介質壓差力打開。

☆ Normally closed type: coil power, the main valve to

 open by medium pressure force; coil power, valve closed 

☆ Normally open type: coil power, the valve closed; coil power,

 pressure forces the main valve opens by media                                                                

備注：當出口端壓力大于進口端壓力，介質回反向?qū)?/span>通。

可安裝止回閥或訂制帶止回功能的閥。

When the exit pressure is greater than the inlet pressure, medium

 Back to pass against the wizard.

Check valve can be installed or ordered withnon-return valve function

四、圓型、方型結構圖及規格尺寸

Round, Square and specifications of size chart

主要技術參數  Main technical parameters

☆產品型號   Product Type:             

☆動作方式：直動式□、分步直動式□、先導式□。

☆Action by: direct-acting type □, direct-action step □, Pilot □.

☆閥體材質：鑄鋼體□、不銹鋼□。（鑄鋼體不能用在腐蝕流體上）                

☆Body material: cast steel body □, stainless steel □. (Steel body can not be used in corrosive fluid on) 

☆控制方式：常開□、常閉□、自保式□。

☆Control mode: Normally open □, NC □, self-protection type □.                                               

☆適用介質：水□、氣□、油□、蒸汽□、燃氣□、腐蝕流體□

☆ Suitable medium: water □, gas □, oil □, steam □, gas □, corrosive fluid □  

☆工作壓力    Work pressure：                                               

1.6mpa□。3.2mpa□。 4.0mpa□。 5.0mpa □。10mpa□。15mpa□.20mpa□.25mpa□. 30mpa□.35mpa□. 40-49mpa□. 50-59mpa□. 60-69mpa□.                                                                                                

☆工作溫度     Operating temperature:                                                

-200℃～0℃□。-60℃～+100℃□。 -20℃～+80℃□。 -20℃～+150℃ □。0℃～+200℃□。0℃～+350℃□.

☆防護性能：防水□、防爆（Exd IICT5）□、防腐□。

☆ Protection performance: waterproof □, explosion-proof (Exd IICT5) □, anti-corrosion □                                              

☆工作電壓       Operating Voltage：                                                                                               

DC12V□、DC24V□、DC36V□、DC110V□、DC127V□、DC220V□;AC36V□、AC110V□、AC220V□、AC380V

☆接線方式：接線座式□、引線式□、插座式□。                                                  

☆Wiring: Wiring Block type □, lead type □, socket□

☆附加功能：帶信號反饋□、帶手動控制□、帶止回功能□

☆Additional features: with signal feedback □, with manual control □, with a return function□

六、安裝與維護Installation and maintenance

☆安裝前應仔細核對閥標牌數據是否符合現場要求，如電壓、溫度、介質、壓力等。

☆電磁閥現場安裝必須按照國家爆炸危險場所“電氣安全規程” 中有關規定進行。

☆電磁閥線圈必須牢固可靠。線圈有三孔插頭，其中上為接地線，左右孔接工作導線。

☆電磁閥安裝前應將管路內部清洗干凈。 

☆如果流通的介質中有雜質，電磁閥進口端前必須安裝密度0.5μm的過濾網。

☆安裝電磁閥時注意閥體上箭頭要求與介質流向一致。

☆電磁閥水平安裝最佳，（線圈在上）。

☆非電氣人員不得拆卸電磁閥電氣部件。

☆Should carefully check the valve before installing signs whether on-site data requirements, such as voltage, temperature, medium, pressure, etc.

☆Solenoid valve must be installed in accordance with the state explosion site dangerous place, "Electrical Safety Regulations" in the relevant provisions.

☆Solenoid valve coil must be solid and reliable. Coil with three-hole plug, which on the ground, then work around hole lead.

☆Solenoid valve installed within the pipe should be cleaned before.

☆If the flow of medium with impurity, solenoid valve must be installed before the inlet of the filter density of 0.5μm.

☆Solenoid valve installed on the arrow when the body demands attention with the same media flow.

☆The level of the best valve installed, (coil on)

☆Non-electrical personnel shall not be demolished solenoid valve electrical components.

七、常見故障診斷及處理： Fault Diagnosis and Treatment

☆接通電源，電磁閥不正常工作 ：a 線圈燒毀或短路——更換線圈，b 電源電壓過低——調整電壓-10%~+10%

范圍。c管道內介質壓力不符合工作壓力范圍 ——調整壓力或更換壓力對應的閥

☆Switch on the power, electromagnetic valve does not work: a .coil to burn or short circuit -------- replace

the coil,b .power supply voltage is too low ------ adjust the voltage of -10% ~ +10%Range.

C. medium pressure pipeline does not meet the scope of work pressure --- the pressure to adjust the

pressure or the corresponding valve replacement

☆ 斷開電源，電磁閥不正常工作閥：閥芯被雜質卡住，不能復位——由專業人員拆卸、清除、裝配。

☆Disconnect the power valve solenoid valve does not work: spool is stuck impurities can not reduction --

the professional demolition, removal, assembly

☆ 泄漏超標：a閥內有雜物——清除雜物，b密封件損壞或老化——更換密封件，c選型壓力不符合工作壓力--

更換壓力對應的閥。

☆Excessive leakage: a valve with debris -- debris removal, b seal damaged or aging --replace seals,

c selection pressures do not meet the work pressure ---Pressure corresponding valve replacement